Theelectropolishing process is well-suited for deburring. During the process, the transfer of metal ions occurs most rapidly on corners or edges of metal parts. Current density or concentration of electrochemical power is greatest at high points, just as lightning is drawn to tall trees and buildings. This helps explain why plating builds metal faster on an edge or burr, while electropolishing (the “reverse” of plating) removes metal fastest at these points.
Properly controlled, the electropolishing process can remove burrs from incredibly complex or fragile parts that do not lend themselves to conventional tumbling or vibratory finishing techniques. The process is best suited for parts having fine blanking, milling, broaching, lapping or grinding burrs. Since electropolishing is non-mechanical, it is important to note that the hardness of a metal part has no bearing on the burr removal. The process works equally well on a fully annealed or hardened part. This is one reason why electropolishing is often specified as a final deburring and finishing process after all fabrication and heat treating processes.
The fact that electropolishing is a non-distorting process is often overlooked. Many metal parts produced today have critical microfinishes or are made from lighter, more fragile materials. In those cases, mass finishing techniques such as tumbling or vibra-finishing create distortion or warping, and can nick or scratch fine finishes. Electropolished parts are never subjected to stress from polishing media, nor are they impinged or tumbled onto each other.
It is important to note that deburring is limited based on burr size, component configuration and amount of stock removal. Larger burrs produced in rough milling or displaced metal from drilling operations often need pre-treatment using other methods. In addition, heavy die break burrs caused by improper tooling maintenance are difficult to remove with electropolishing alone.
Electropolishing, with its ability to remove a microscopically precise layer of surface material with consistent results, is the finishing process of choice for such parts, for many reasons. Learn why electropolishing is more effective than other methods for removing burrs.
Discover why one of the most common applications for electropolishing is to enhance corrosion resistance on a wide variety of metal alloys, specifically stainless steel. These two case studies show why electropolishing has become a replacement process for passivation.
Do your stainless steel parts have extra material or burrs? Able Electropolishing can help. Through our proprietary electropolishing or reverse plating process, we have been deburring stainless steel and many other alloys since 1954. Our staff of knowledgeable technicians are dedicated to finding the most cost-effective methods for removing burrs from stainless steel. We can provide deburring services for stainless steel even in the most hard to reach areas –and we can do all this without affecting the strength or structure of your valuable steel parts.
At Able, we implement a wide assortment of techniques to remove burrs from stainless steel. During the process, the transfer of metal ions occurs most rapidly on corners or edges of metal parts. Current density or concentration of electrochemical power is greatest at high points, just as lightning is drawn to tall trees and buildings. This helps explain why plating builds metal faster on an edge or burr, while electropolishing (the “reverse” of plating) removes metal fastest at these points.
Properly controlled, the electropolishing process can remove burrs from incredibly complex or fragile parts that do not lend themselves to conventional tumbling or vibratory finishing techniques. Since electropolishing is non-mechanical, it is important to note that the hardness of a metal part has no bearing on the burr removal.
Additionally, since electropolishing is a non-distorting process, your stainless steel parts are never subjected to stress from polishing media, nor are they impinged or tumbled onto each other.
The 400 series stainless steel component pictured is the inner portion of a dual drill bit assembly used for surgery on the human brain. Grinding and/or machining burrs prevent the mating parts from freely rotating (one bit within the other), while burrs specifically on cutting edges reduce ease and rate of cutting. Increased pressure on the drill bit due to contaminated cutting edges affects the functionality of the cutting device’s clutching mechanism; the sharpness of the bit is tied directly to the function of the rest of the device. In addition, if not properly removed, burrs may flake or chip off causing a potential bio-hazard for the patient.
By precisely removing .0005″ +/-.0001″ total material off of the drill bit’s O.D., electropolishing the stainless steel part preserves edge condition while removing problematic burrs. As in this application, electropolishing is often a superior alternative to hand deburring; the electropolishing process offers greater consistency from part to part, and is significantly more cost effective. Deburring the part while maintaining sharp cutting edges, electropolishing allows the cutting device to function smoothly, efficiently and safely.
The part pictured is a 420 stainless blade used on high-end vegetable peelers. After the grinding operation, the blade edges are left sharp, but ragged. Pictured parts on the left side of the page illustrate the burrs post-grinding. The grinding burrs need to be removed in order for the blade to slide and cut smoothly—it is also important for this product to be clean and free of any metal shavings, as it comes into direct contact with food. After researching various deburring options, the manufacturer of this high volume product found electropolishing to be the most consistent and cost effective method to finish the blade component of the peeler. As the final operation, electropolishing is useful for both deburring and cleaning the part. In this case, .002″ total material is removed from the thickness of the blade which, after extensive sampling, was proven to be the optimal amount of removal. Once electropolished, the blades are burr-free and sharper than in the “as-ground” condition.
Our tightly controlled quality process and ISO 9001 and ISO 13485 certifications make us the preferred partner for many medical device manufacturers across the globe. From implantable devices to surgical instruments, electropolishing is a single-process treatment that results in biocompatible, safe and ultra clean parts.Learn More
We offer aerospace vendors and original equipment manufacturers our signature metal finishing services to increase fatigue-resistance for their metal parts, rendering them capable of withstanding the stress and corrosion that comes with long-term use. Surface abnormalities lead to part failure, but with electropolishing, parts become more reliable and long lasting.Learn More
Our strict adherence to industry standards ensures that pharmaceutical components are electropolished in accordance with ASTM B912 and ASME BPE specifications. These products are clean and smooth, corrosion resistant and contaminant free.Learn More
Corrosion resistance and microfinish improvement are essential for critical automotive parts, making electropolishing an increasingly beneficial option for automakers. Electropolishing both interior and exterior auto parts ensures they will resist premature failure and function at an optimal level.Learn More
Notable examples of appliance parts we electropolish are 400-series stainless steel alloys used in many consumer appliances. Our metal finishing services help increase corrosion resistance for these parts, and by removing the outermost layer of metal withelectropolishing the durability and longevityof these appliance components is increased.Learn More
We have a long history of working with the food and beverage industry. Electropolishing materials for this industry eliminates the buildup of bacterial biofilms, as well as keeping the equipment free of contaminants like Salmonella. When it comes to food and beverage processing equipment, safety and cleanliness are of the upmost importance and electropolishing delivers the level of sanitation required by a number of regulatory agencies.Learn More
From robotics to heavy mobile equipment, the uses of electropolishing in the hydraulics and pneumatics industry are many. By helping prevent premature part failure, electropolishing reduces the amount of downtime and increases the life cycle of these components. Proper surface finish and cleanliness is key in this industry, and electropolishing attains the finishour customers require.Learn More
Improving conductivity and performance is just one benefit electropolishing offers for electronics parts. The surface finish is improved by as much as 50 percent, removing imperfections from the material without removing a lot of material removal from the component.Learn More
The largest design and contract manufacturing show in North America, the Akron Design-2-Part Show is the most efficient place to meet hundreds of high-quality American suppliers of custom parts, stock parts, and manufacturing services.
John S. Knight Center | Akron, OH
The MPO Summit has provided the medtech industry with an opportunity for interactive networking and educational presentations for outsourcing for medical device manufacturing for over 15 years.
Grand America Hotel | Salt Lake City, UT